News:

Don't forget to read the forum rules.

Main Menu
Menu

Show posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Show posts Menu

Messages - Parttimesavant

#1
Thank you for the input bjammerz. A helpful note about the headphone jack. Yes, with headphones plugged in there is buzzing in both ears and that means somewhere in the amp is the culprit. Hmmm....Still looking.
#2
Ah yes, the old solder joint scenario. I spent a few weeks wondering why the 72' had no sound when I first got it. I went over the 24v regulator, amp modules, preamp, and all sorts of odds and ends only to find that there was a resistor that Fender Rhodes had never soldered to the board! Yes, always look carefully at all solder points. Thanks again.
#3
I have checked the 4 pin connector on the amp for continuity and good connection and it passed. I also sprayed some CRC contact cleaner on it for posterity. The buzz is coming from somewhere else in the amp.
#4
I have 2 four pin cables and have used them interchangeably on both suitcases. No buzzing on the 72' with either cable. I will have a closer look at the amp connector though.
#5
I have two suitcases, one from 1972 and one from 1973. The 73' has a rather angry sounding buzz coming out of both channels when the preamp in connected to the amp. The amp has no buzz when the preamp is disconnected. I have reasoned that the problem is not in the preamp however,  since I have used the piano tops of both suitcases with the 72' speaker bottom demonstrating buzz and hum free operation. This leads me to believe that the problem is somewhere in the main amp of the 1973 suitcase. I investigated the possibility of bad filter caps and then went about putting two 3300 mf 50V caps across the rectifier bridge. There was no change to the mean buzz sounding from the cab. Are there a some other points anyone could tell me to check over to figure out where this buzz could be coming from? Thanks for any help forum.
#6
Thanks everyone for some really well informed answers! Tone still sounds pretty good. Will hold off on recapping till something is calling for it.
#7
How can I tell when my Peterson preamp is in need of capacitor replacement? 
#8
Well, after hearing what sounded like a greater bass response on the right side of the cab from the player side facing it, I considered the ported effect and just thought I would swap the speaker plugs on the amp inside to see what would happen. To my surprise, the bass response went to the left side of the cab! So I now know that while the acoustic effect of the porting is a reality, it is not enough in this case  to cause the one channel to sound with more tone to one side. I had to dig deeper.......On each of  the amp modules inside the cab is a variable resistor that that governs gain control. I found that I could perfectly balance my A and B channels to my liking just by making the gain adjustments from the amp modules! I would recommend that anyone having trouble with "uneven" vibrato or the like to consider a gain adjustment from these points once they can determine that all components on the modules and preamp are functioning normally. 
#9
Solved! Thank you Max for a well thought out, careful, and accurate response.  I would also like to thank you for your note of safety. It benefits a forum very much when people make an effort to take care with potentially dangerous things. 

I have poured over this issue for some time testing components individually and so on with all sign pointing to good regulator function. After a short break and some time away from the project, it appeared that the factory at Fullerton revealed some unfinished business. One of the leads to a 470 Ohm resistor that sits on the regulator board was never soldered to the board! It had the characteristic squashed\cut leads that the factory used to hold the components to the board better (making removal difficult) and holding this resistor in place with no solder since 1972. After all this time going over and over all other points on the unit, I need to stress the importance of prioritizing diagnosis. I had checked all solder points for cracks and such as I would do in any electronics examination, but, it goes to show that it's important to take time with the simplest possibilities first as one can spend much more time on the complex ones. Such was the case here. I encourage anyone with a similar 24 volt regulator issue to THOROUGHLY check your solder points!

There is on last thing. Now that it is working through the speakers it seems one channel is favoring more tone. Not so much as to say that one side is louder than the other, but when the vibrato is at max intensity and slowest speed with bass notes played it is more "tonally" pronounced in one of the channels. It is as if one channel has been EQ'd to bring out more low mid. How can we balance these channels? Could this be a case for a preamp recap or amp module rebuild?

     
#10
Thanks for the reply. I had already checked the harp RCA connector at an earlier time in the troubleshoot though. 
#11
First I'd like to assure anyone that would like to assist me here that I have some basic experience working on electronics and am informed well enough to work safely on these components. I have referenced the schematics and repair vids from Vintage Vibe and have tested all points usually associated with 24volt regulator issues. These include correct readings on the regulator connectors......+24 volts on the middle -36 and +36 to the left and right on both connectors. I have also gotten a good reading from the 5 Ohm 10 Watt resistor connected to the regulator. I have a good functioning preamp that sounds great going through two other 4 pin suitcase bottom power supplies, but when I connect the same prepamp  to the supply in question it shows no activity even though there is 24 volts across pins 1 and 4 right up to the pre amp end of the cable. The power modules are fine as I have also tested them separately. So, with a good preamp and 24 volts coming right up to it, what could it be? Should the 24 volts at least be able to power the prepamp enough to see the vibrato lights come on or hear a signal through the headphone jack without having the supply connected to the amp modules? Could there still be a problem with the 24v power transistor even though it shows a 24v reading at the module connectors? I have searched for similar instances of this problem in as many places as I can. Vintage Vibe does not currently have an electronics tech available so I reach out to this knowledgeable forum. Thanks for any assistance and happy holidays. -Mike         
#12
I have checked the  24, -36, & +36 voltages, and they are all good. I have measured all resistors and transistors on the board and they read correct. I know the preamp is working normally as I have checked it using a cheek block power supply. I have also gotten a 24v reading on pins 1 and 4 on the end of the cable to the preamp to take the cable out of the mix. So, it appears I am getting 24 volts to the preamp and there is no activity. There is no vibrato, no signal from the preamp, so on.
I would assume that the  24v regulating transistor would not be able to send 24v if there was an issue with it. If the transistor is ok, could one of those old white Mallory caps be the source of this problem if all resistors and transistors check out? I know it is not the Zener diode because that would cause a very low reading on the 24v test point. I am assuming the two power amp modules do not need to be connected to the main amp in order for the preamp to function normally- to listen for signal through the head phone jack or see if the vibrato bulbs are lighting. Any ideas?     
#13
This is what makes a forum great. Thank you Charlie!
#14
Does anyone know the exact length that the wood post inside the suitcase that links the sustain pedal to the keyboard should be?
#15
Is the main amp from a 1980 Rhodes suitcase (Black grill cloth, 5 pin) designed to handle a 4 ohm load? The 4 Speakers in the cabinet are each 8 ohm and look like they should wired in parallel, this adds up to 4 ohms per each channel of the amp.  Is this wiring correct for this amp? Can anyone confirm? I have scoured the the net for info about this and all I can find are details about the earlier 80watt 32 ohm speaker version. Thanks for any info.
#16
Is the main amp from a 1980 Rhodes suitcase (Black grill cloth, 5 pin) designed to handle a 4 ohm load? The 4 Speakers in the cabinet are each 8 ohm and look like they are wired in parallel, this adds up to 4 ohms per each channel of the amp.  Is this correct for this amp? Can anyone confirm? I have scoured the the net for info about this and all I can find are details about the earlier 80watt 32 ohm speaker version.