News:

Shipping now! "Classic Keys" book, a celebration of vintage keyboards  More...

Main Menu

FIXED - another Rhodes risen from the dead - thanks, Mark II

Started by benmeza, September 01, 2008, 12:21:46 PM

Previous topic - Next topic

benmeza

...the metal casing is showing continuity points between the pins 1 & 5.  I just got it in from Vintage Vibe - can anyone use a continuity tester on their known working 5 pin cable to see if their pins 1, 5, & case are all showing continuity together?  I plug it into my suitcase top and bottom and the preamp light comes on but I get no sound and the trem light will not come on.  The preamp might be out on my rhodes top since I pieced together the top and bottom to get my suitcase system, but I'm trying to troubleshoot the easiest problem first before I tear into the electronics.  Thanks for your help!


EDITED Subject title to reflect my realization that I likely have a problem within the power regulator section - maybe the power taps aren't giving out the right voltages?

benmeza

...nevermind.  I now see the part in the amp differences page that covers that.  Looks like Pin 1 should be Ground and Pin 5 should be 15v DC....I wonder why my preamp light was coming on if the +voltage was just going to ground?

Mark II

how do you measure: with 5 pin cable unplugged or not ?

Mark II
Rhodes Stage 73 Mark II 1980 / modified Peterson Suitcase Preamp

benmeza

Unplugged - just pin to pin after I unscrewed the back off the right angle connector to get to the solder joints.

Mark II

check the socket without 5 pin cable plugged in.

After that check the 5 pin cable.

Mark II
Rhodes Stage 73 Mark II 1980 / modified Peterson Suitcase Preamp

benmeza

Okay, checked the cable as you had mentioned and I even dug out my more precise leads for the voltmeter.  I think the larger leads I was using were accidentally touching ground which was why those pins were showing continuity.  Turns out the cable is just fine.  What was alarming is the pin2 & pin5 voltages are around 240V which is not anywhere close to 15V....so if I can get this stupid stripped screw off, I'll check the power coming out of pin 2 on the regulators and going in on pin1 after the diodes.  I suppose something is weird with one of those sets of components....more to follow.

Mark II

oh man.
240 Volts on pin 2 and 5 ?
dont mess with this voltage. It bites !

what kind of power supply are you using ? A regular speaker cabinet or a custom made ?

Mark II
Rhodes Stage 73 Mark II 1980 / modified Peterson Suitcase Preamp

benmeza

I believe it's all original....I'll have some time to tear into it later this morning to really tell.

benmeza

Okay - so I finally did a little testing and it's odd and I'm not quite sure who the culprit is.  My dad must have had the wrong settings on the previous multimeter results I posted(plus the battery was dying) so he may have been reading ghosted numbers - his eyes aren't so good anymore.  Anyway, I put a fresh battery in and did a little poking around last night and think I got the right voltages this time.  So my Regulator board gave me the following:

A1:
Pin1: 15v
Pin2: -0v
Pin 3: 15v

A2:
Pin1: 45v
Pin2: 30v
Pin 3: 15v

...that gives me 30v at pin5 on the preamp cable and 0v at pin2.  So I know after the voltage regulator I'm not getting the proper voltages and it appears as though I'm not getting the proper voltages before it either meaning my problem is either the diodes or the transformer itself - or I guess one of those filter caps could have went out.  Any idea what I should be getting at those points and how I can check?  I'm a relative newbie to debugging and though my Dad knows some stuff(went to electronics school), he's also the guy who will spend hours working on something "broken" before he realizes he forgot to plug it in ;-)

 The weird thing is the power amp works fine for line in stuff but now that I have been poking around I noticed there is a faint buzz when I first turn the amp on that fades away after a few seconds....maybe it is the caps in the preamp section.  Hmm.....  Ideas?

Mark II

Quote from: "Mark II"
what kind of power supply are you using ? A regular speaker cabinet or a custom made ?

Mark II

I must repeat myself as I am kind of confused. And that is a bad state in order to give some advice.

What does A1 and A2 refer to ?
Is that the regulator board you are talking about ?
http://www.fenderrhodes.org/ch11/fig11-5.jpg

here is the schematic of the hole powe amp of 5 pin suitcase pianos:
http://www.fenderrhodes.org/ch11/fig11-3.jpg

kind regards
Mark II
Rhodes Stage 73 Mark II 1980 / modified Peterson Suitcase Preamp

benmeza

No problem - I appreciate the help.  So I have the 5 pin Rhodes top with the EQ sliders and a 5 pin Rhodes suitcase cabinet bottom - the 100 watt variety I believe.  The side panel looks exactly the same as the one listed in your "missing suitcase channel" sticky.  Mine has the inputs that can be fed into the amp and both inputs work fine.  

I don't believe there have been any mods to the cabinet/amp except for one replaced speaker.  Otherwise it appears to be all original with the same caps you would expect to see in Fender guitar amps of similar vintage.  

A1 and A2 refer to the regulator board - sorry I wasn't clear on that earlier.

Mark II

alright. now I got you.

basically with these voltage regulators A1/A2 is has to be that way
they are regulating the DC voltage, reducing the riple of the DC:

A1
pin 1: ground 0 V
pin 2: -15 volts DC
pin 3: round about -18 volts DC

A2
pin 1: round about +18 volts DC
pin 2: +15 volts DC
pin 3: ground 0 V

So, in your case there is a mess on this PCB. But fortunatly there arent that many parts. Check the harness. are all solder joints good ?
How about your technical skills ? Do you know how to solder ?

Mark II
Rhodes Stage 73 Mark II 1980 / modified Peterson Suitcase Preamp

benmeza

I'm decent at soldering, can read a schematic, and use a voltmeter(despite my earlier gaffe)...I just don't know all the formulas or how to check specific components like caps/resistors(outside of obvious physical damage in old caps).  

...I'll tear into it today and see about those solder joints/harness.  I believe it's just those three harness points, the four caps and the diodes to check.

Mark II

OK.
basically I would do this after the things mentioned above (harness, solder joints). unplug the 5pin cable from the preamp. you will need to get the panel with all the electronics in a safe state that you can power the unit and measure without touching dangerous voltages.

open the schematic for comparing my thoughts.
start with the transformator (although it's unlikely that the winding is gone bad).
unplug the regulator board and measure at P3 pin 5 and 6.

the regulator board is delivering 15 volts. so it's input must be 15 volts plus the voltage drop of A1/A2. so, both regulators need +- 18 volts DC. the input of the rectifier (diodes CR1 to CR4) = output of the transformator is an AC voltage.
the transformator will supply round about 13 volts AC.

So with one probe of a multimeter connected to pin 5 and the other to pin 6 of P3 you should read ~13 volts AC.
I would confirm this reading.

Next: find a solid ground connection for the next measurements. this could be the minus poles of the big caps for the +-30  volts DC for the main amp. check the voltages for the main amp aswell. when you read +-30 volts DC at the plus poles of the caps you are sure to have a solid ground. and that should be the case as the main amp works - as you mentioned.

section 1:11 to 1:49 of this video gives you a good example.
http://www.youtube.com/watch?v=KNfxngocnWs

next: input of both regulators A1 and A2.
unsolder pin 3 of A1 and pin 1 of A2 and check the voltages at the solder taps (not the pins of the regulators). you should have the +18 volts DC at A2 and -18 volts DC at A1.

check the pins of the regulators. they should all read 0 volts as their inputs are disconnected.

to be continued.
it's getting late.

kind regards.
Mark II
Rhodes Stage 73 Mark II 1980 / modified Peterson Suitcase Preamp

benmeza

Success!

.....so I toyed around with the harness to make sure everything was seated properly and at first it seemed like it was but a little shake and nudge and it went in a little further - I think there must have been something prevented it from being fully seated.  Anyway, after that I got all the expected voltages at the XLR out on the amp.  I plugged the XLR in and it still wasn't working so I did the "jiggle" and found the cable I got from Vintage Vibe did in fact have a small short - the ground cable on the male side was cutting into the red pin 5 cable so depending on how you had jarred it last, it would either work or not.  

Anyway, corrected the problem and now I have beautiful stereo tremolo!  One more Rhodes resurrected from the dead!!!  With that, I still have to repair one last dead pickup, tweak the damper a bit, and give it a good tune and this baby will be 100% in working order.  I replaced over 25 dead pickups in this thing - was able to rewind most of the bad ones though.  The damper problem is just a little tweaking I think - it just seems to be uneven.  In half damper position it seems to let the bass & high notes ring but the middle keys give a thud a bit so you have to really mash down on the sustain pedal to get the whole board to sustain....and then it's time to tune!  I already set the tine positions, escapement, etc.  

Thanks, for all your help, Mark II - your a true asset to this community!

Mark II

you are welcome. enjoy your rhodes.

kind regards.
Mark II
Rhodes Stage 73 Mark II 1980 / modified Peterson Suitcase Preamp