News:

Follow us on Twitter for important announcements and outage notices.

Main Menu

Fender Rhodes Pickup Rewinding Project

Started by okie, January 20, 2018, 01:07:01 PM

Previous topic - Next topic

okie

Been wanting one forever even though I'm not a keys player but the prices on these are all over the place. Found this one 2.5-hrs from me on craigslist and worked out a straight trade for a guitar. It's a 1979 Mark I 73 and it was in very good cosmetic condition. Problem was 69 dead pickups due to corrosion on the coil wire start, no way to repair without unwinding and rewinding pickups. Was not going to pay $828 for 69 new ones at $12/each.

Took it all apart for general cleaning and cleaned the tone bar and tines with scotchbrite, harp had some corrosion on it so I sanded, primed, and painted it. Replaced the grommets and screws and repaired a few bridal straps, some new case hardware, replaced a few missing hammers, new logos, and, misc. missing parts. Action was now great and it looks mint.

The fun part was unwinding and rewinding the pickups. I scoured the interwebs and found some videos and information on EP-forum. I tried unwinding them onto a spool and rewinding them back on, a no go for me due to constant breakage of wire. Decided to just unwind all of them and use new wire. Drilled a small hole in a piece of wood and built a jig to hold and unwind the pickups by hand. Hours later they were unwound.

Saw a video of someone using a laser counter to count the number of wire turns and found a used one on ebay for cheap. I used Temco 38 Awg wire and it took 2900+/- turns with the laser counter for the 190+/- ohms needed. I used 8 oz. spools as I figure it would be less of a load on the wire when spooling it onto the pickups. I controlled the drill speed with my left hand and used my right hand to guide the wire onto the pickup bobbin, back and forth, back and forth. Took about 3-4 minutes for each pickup. I went pretty fast with the drill and did not have a single wire break with this setup using the 8 ounce spools. I used ½" Kapton tape over the rewound coil wire.

Installed the rewound pickups and soldered them with new hookup wire. Tuning and adjusting tone took quite some time but it now plays and sounds amazing.

I had zero experience with a Rhodes before this but it was fairly easy but very time consuming.  Very satisfying bringing this back to life and back in use.   Many thanks for the information I gleaned from this forum.

Every pickup had corrosion breaks at the coil beginning:



Unwinding by hand:







Rewinding jig and laser counter:













All done and in it's new home:







bourniplus

Awesome, thanks for sharing.

The M3 will be in good company.

okie

Thanks!  Yes going for the classic tones with the Hammond and the Rhodes.

d-rock


pnoboy

Good work!  I should note that it is the number of turns that is most important, not the resistance.  That is, once one has selected the wire, the pickups should all be wound with the same number of turns.

okie

Quote from: pnoboy on January 22, 2018, 11:37:19 AM
Good work!  I should note that it is the number of turns that is most important, not the resistance.  That is, once one has selected the wire, the pickups should all be wound with the same number of turns.

Thanks!  Yup that's what I did, I first tried 3000 turns and it put the pickups at around 200 ohms, too hot.  then I tried 2900 turns and it put it right around 190 ohms, from then on I stopped at 2900 turns for each pickup.  I checked all the pickups anyway and there were all right around 190 ohms.

rgkemm

Great job.  Looks beautiful!

Question. I'm new to the forum and have just started refurbing a Mark I.  You mentioned above that "Every pickup had corrosion breaks at the coil beginning."  Can you help me understand how to identify that? You have a photo underneath the quote, but I'd like to know specifically where it's referring to, so I can check the same on my own piano.

Thanks!

sean

#7
Get a bright flashlight, and a high-power magnifying glass.

Start at the top end of the piano where the tonebars are not in the way, and look at the pickup wire to search for green corrosion.  Look specifically at the part of the wire as it leaves the left side of the solder tab at the back of the pickup (the end of the pickup away from the pickup tip).  As this wire leaves the solder blob, it turns down over the nylon bobbin to go down into the center of the coil winding.  The place where the wire sits against the top of the bobbin seems to favor the development of corrosion.  It is Statue-of-Liberty green in color. 

The corrosion is common.  On the piano I have open in the living room, three of the top twenty pickups show a strong green color.

The green corrosion can progress to the point where the conductor breaks, and the pickup goes dead.

I personally would not try to scrape off the green dust, because you risk breaking the wire.  I wonder if a drop of SuperGlue, hairspray, or nail polish would stop the corrosion from progressing further.


Oh, I forgot:  this corrosion can also break the wire near the other solder terminal (at the pickup tip).  A break at this terminial is less problematic, because you can simply unwind one single turn of the winding and re-solder it to the terminal.

Theoretically, the break near the back terminal can be repaired as shown by http://www.fenderrhodes.com/service/rewinding-pickups.html.  However, no known 21st-century human has shown the patience to do this.

Sean

okie

Sean described it perfectly.  Here's the same pic with the problem break area circled.  This is at the coil start so not a way to unwrap and resolder if there is a break.  None of mine had issues at the coil end which would have been simple to unwind and resolder.  The breaks and green corrosion on mine were really bad.


rgkemm

Excellent! Thank you both for the clarification and the visual reference. I'll check mine out.

adcbicycle

Good work!!
My pick up winder project has stalled, but I'm very close.
https://www.youtube.com/watch?v=ffbsw7MbhUI

I'm currently adding a rotation counter made from cheap digital counter like this:


okie

Quote from: adcbicycle on February 20, 2018, 10:53:39 AM
Good work!!
My pick up winder project has stalled, but I'm very close.
https://www.youtube.com/watch?v=ffbsw7MbhUI

I'm currently adding a rotation counter made from cheap digital counter like this:



Nice use of technology!